Lazer Gaming Mouse: Scenario not working properly on Railworks 3 Train Simulator 2012

Scenario not working properly on Railworks 3 Train Simulator 2012
I am having a problem with "moving boxes" Scenario. I leave the station wagon - no problem. Just before reaching the drop off point we join the main trail and then cross a bridge. For some reason I do not understand, is derailed at all times. I've tried running it as slow as 5 mph at a speed between that and 20 mph (limit is 25 mph), but no matter what speed you always derails. Ariel finally got in sight and found that as the train goes over the bridge, half the length of training derailed truck only. Not sure if the points are being reset or what, but that's what it seems.

#2
24-09-2011
RyanInt
Member

Join Date: Jun 2009
Posts: 3,970
Re: Scenario not working properly on Railworks 3 Train Simulator 2012
Do not know this scenario, but there are two things to do. First check the game files. Open Steam, go to libraries. Right click on Railworks 3 Train Simulator 2012 > Properties> Local Files tab> Verify. Second, when you start Railworks 3 Train Simulator 2012, on the main windows, before you click "Start" goes to the tools and documents tab and clears the cache of the plan.

#3
24-09-2011
Common
Member

Join Date: Jun 2009
Posts: 4,020
Re: Scenario not working properly on Railworks 3 Train Simulator 2012
I used to find the exact same problem in this scenario. It consists of the "bad" nature of container flat cars, specifically in its dampers markedly enlarged. In the tight corners that are often wedged between other, causing a derailment, as they are very strong (in the game, of course) and can cancel the entire car. There is no specific solution and 100% of work as far as I know. Try to check the shock absorbers and change before leaving the free movement of the camera when the train is about to enter into the problem area. Watch for any "good" vehicle combination and if you see a problem, stop the train as quickly as possible and uncoupling the respective coaches and the couple again to "fix".

#4
24-09-2011
MacIntel
Member

Join Date: Aug 2009
Posts: 3,734
Re: Scenario not working properly on Railworks 3 Train Simulator 2012
Try to start and run it to the stage just before the problem, save, exit, then resume.

#5
24-09-2011
desilva
Member

Join Date: Apr 2009
Posts: 3,947
Re: Scenario not working properly on Railworks 3 Train Simulator 2012
I suggests in Edit Mode passing by rolling stock, rolling stock overlap each other, sometimes instead of multiple strings in one or more cars. To correct his, flying lower left, click "consists Select" that by clicking on a chain of car move a little and that will be corrected automatically and the problem of ghosting, check other tracks of the same, then SAVE. Now you do not have this problem comes up again, unless, of course, these facts are evident in the stage somewhere in the grid areas others.

#6
24-09-2011

Squibbit
Member

Join Date: May 2008
Posts: 4,061
Re: Scenario not working properly on Railworks 3 Train Simulator 2012
If above all solution not working to solve the issue and after that I would like to suggest you to make contact with the support of the game or steam and after that go through your issue and they will solve your issue. Even I have gone through this issue and after that I have made contact with the support and after that they have solved mine issue and so I would like to suggest you this.

#7
25-09-2011
AZUL
Member

Join Date: Jun 2009
Posts: 3,864
Re: Scenario not working properly on Railworks 3 Train Simulator 2012
If above all solution not working to solve the issue and after that I would like to suggest you o make uninstall the Railworks 3 Train Simulator 2012 game and after that make sure your getting the issue or not. Even I have faced the issue and after that I have just reinstalled the Railworks 3 Train Simulator 2012 game and after that I have solved mine issue.